{{ $t('Pin') }}		{{ $t('Name') }}	{{ $t('Description') }}
TS801	TS802
1	5	SDA	{{ $t('TestPinpleaseconnecttoground') }}
2	4	GND	{{ $t('pin13') }}
3	6	SCL	{{ $t('TestPinpleaseconnecttoground') }}
4	1	VCONN1	{{ $t('VCONNInputPowerPin') }}1
5	2	CC	{{ $t('USBTypeCCClineinputandoutput') }}
6	3	VCONN2	{{ $t('VCONNInputPowerPin') }}2
7	7	EPAD	{{ $t('pin13') }}

{{ $t('PARAMETERS') }}	{{ $t('RATINGS') }}
VCONN1 / VCONN2 / CC	-0.5V to 7V
SDA、SCL、CC to GND	-0.5V to 3.6V
Storage Temperature	-65℃ to 150℃
Operation Temperature	-40℃ to 85℃
ESD HBM – CC / VCONN1 / VCONN2	± 8KV
ESD HBM – SDA / SCL	± 5KV

{{ $t('Package') }}	θJA	θJC	{{ $t('UNIT') }}
DFN-6L (2mm x 2mm)	45.5	11.7	℃/W

{{ $t('Parameter') }}	{{ $t('Symbols') }}	{{ $t('Min') }}	{{ $t('Nom') }}	{{ $t('Max') }}	{{ $t('UNIT') }}
BMC Signal (Test Condition: VCONN = 3V to 5.5V)
Bit Rate	fBitRate	270	300	330	Kbps
Maximum difference between the bit rate during the part of the packet following the Preamble and the reference bit rate	pBitRate	---	---	0.25	%
Time from the end of last bit of a Frame until the start of the first bit of the next Preamble.	tInterFrameGap	25	---	---	µs
Time before the start of the first Bit of the Preamble when the transmitter shall start driving the line.	tStartDrive	-1	---	1	µs
BMC Common Normative (Test Condition: VCONN = 3V to 5.5V )
Time to cease driving the line after the end of the last bit of the Frame.	tEndDriveBMC	---	---	23	µs
Fall Time	tFall	300	---	---	ns
Rise Time	tRise	300	---	---	ns
Time to cease driving the line after the final high to low transition	tHoldLowBMC	1			µs
Voltage Swing	vSwing	1.05	1.125	1.2	V
Transmitter Output Impedance	zDriver	33	---	75	Ω
Transmit Low Voltage		-75	---	75	mV
BMC Receiver Normative (Test Condition: VCONN = 3V to 5.5V)
Cable Termination	RA	800	---	1200	Ω
Receiver Input Impedance	zBmcRx	1	---	---	MΩ
Time Window for Detecting Bus Non-idle	tTransitionWindow	12	---	20	µs
Number to Count to Detect Bus Non-idle	nCount	3	---	---
Time constant of a single pole filter to limit broad-band noise ingression	tRxFilter	100	---	---	ns
General Parameters
TVCONN1/VCONN2 Voltage	VCONN	2.75	5	5.75	V
Operation Current (VCONN = 5V)	IOP	---	4	---	mA
Standby current (VCONN = 5V)	Istandby	---	1.6	---	mA
Operating Junction Temperature	TJ	-40	---	125	℃
Operating Ambient Temperature	TA	-40	---	85	℃

ID Header

Bit(s)	Descriptions	Note
Bit [31]	USB communications capable as USB host: 0b: Otherwise	(Fixed)
Bit [30]	USB communications capable as a USB device: 0b: Otherwise	(Fixed)
Bit [29:27]	Product type (cable plug): 011b: Passive Cable	(Fixed)
Bit [26]	Modal operation supported: 0b: Otherwise	(Fixed)
Bit [25:23]	Product Type (DFP): Reserved, Shall Not be used	(Fixed)
Bit [22:21]	Connector Type: 11b: USB Type-C Plug	(Fixed)
Bit [20:16]	0: Reserved, shall not be used	(Fixed)
Bit [15:0]	16-bit unsigned integer. USB vendor ID (0x30AC)	(Fixed)

Cert Stat VDO

Bit(s)	Descriptions	Note
Bit [31:0]	32-bit unsigned integer, XID (0x00002714 = 10004)	(Fixed)

Product VDO

Bit(s)	Descriptions	Note
Bit [31:16]	16-bit unsigned integer. USB Product ID (0x3001)	(Fixed)
Bit [15:0]	16-bit unsigned integer. bcdDevice (0x0000)	(Fixed)

Passive Cable VDO

Bit(s)	Descriptions		Note
Bit [31:28]	Cable HW Version	0000b	(Fixed)
Bit [27:24]	Cable Firmware Version	0000b	(Fixed)
Bit [23:21]	VDO Version	Version number of the VDO (not this specification version): Version 1.0: 000b	(Fixed)
Bit [20]	Reserved	0: Reserved, shall not be used	(Fixed)
Bit [19:18]	USB Type-C plug to USB Type-C/Captive	00b: Reserved, Shall Not be used 10b: Type-C	(Fixed)
Bit [17]	EPR Mode Capable	0: Reserved, shall not be used	(Fixed)
Bit [16:13]	Cable Latency	0000b: Reserved, shall not be used 0001b: < 10ns (~1m) 0010b: 10ns to 20ns (~2m) 0011b: 20ns to 30ns (~3m) 0100b: 30ns to 40ns (~4m) 0101b: 40ns to 50ns (~5m) 0110b: 50ns to 60ns (~6m) 0111b: 60ns to 70ns (~7m)	(Optional)
Bit [12:11]	Cable Termination Type	00b: VCONN not required. Cable plugs that only support discover identity commands shall set these bits to 00b.	(Fixed)
Bit [10:9]	Maximum VBUS Voltage	Maximum Cable VBUS Voltage: 00b: 20V 01b: 30V 10b: 40V 11b: 50V	(Optional)
Bit [8:7]	Reserved	00b: Reserved, shall not be used	(Fixed)
Bit [6:5]	VBUS Current Handling Capability	00b: Reserved, shall not be used 01b: 3A 10b: 5A 11b: Reserved, shall not be used	(Optional)
Bit [4:3]	Reserved	Shall be set to 0.	(Fixed)
Bit [2:0]/td>	USB SuperSpeed Signaling support	000b: USB 2.0 only, no SuperSpeed support 001b: [USB 3.2] Gen1 010b: [USB 3.2] Gen1 and Gen2 See [USB Type-C 1.3] for definitions.	(Optional)